Quick Tips!

Mazda 5 Speed Manual
Transmission


Explorer Wheel Bearings


Explorer Computer Chip


Explorer Fuel Pump RFI


Explorer Dual Batteries


Cleaning Ford Explorer MAS


Explorer Caliper Slide Pins


Explorer Shock Skid Plate


Explorer K&N Filtercharger


Explorer Disc Brake Rear Axle


Explorer Body Lift Install


Explorer Dual Shocks


Explorer Steering Stabilizer


Explorer 2.5" Lift Install


Speedometer Calibration


Explorer Torsion Bar Lift


Explorer Disc Brake Swap


Explorer Rear Axle Seals


Explorer Manual Hubs


Atlas II Transfer Case
in Ford Explorer


KKM Air Filter Review

Explorer White Face Gauges


Ford Explorer Clutch
Bleeding Procedure


Spindle Nut Upgrade


Ford Explorer 2wd - 4wd
Conversion


1991 - 1994 Ford Explorer
Tire Options


1995 - 2001 Ford Explorer
Tire Options


Ford Explorer Spring Over
Axle Conversion


Ford Explorer Vibration Problems


Ford Explorer 5 Link Solid
Axle Swap Dana 44


Installing Rock Sliders on a
Ford Explorer

Ford Explorer Overhead
Console Install


4.0 Valve Clatter in Ford
Explorer and Ranger


Huge List of Maintenance Tips
for the Ford Explorer


Setting up Ford 8.8" Gears


4x4 Shift Motor Rebuild


Body Work 101 w/photos


C4 Transmission Dana 20

 Transfer Case Swap into Explorer


A4LD Rebuild Diary


Dana 44 TTB Knuckles on
 Dana 35 TTB Axle


A4LD Front Seal Info


Max Tire Size for Explorer


Ford Explorer Torsion Bar
 Removal Installation


Front Differential
R&R 1995+ Explorer

Converting R12 to R134A
 in Ford Explorer

700R4 Transmission Swap

Explorer Sport Truck

Fiberglass step by step

Wheel Offset Backspace

Wheel Spacers

IAC Valve Cleaning

Explorer Message Board
 Home PageMessage BoardBookstoreResourcesFAQTipsReviewsReaders RidesAddMore ExplorersExplorer RunsWhoopsSave TrailsLinksHam Radio


Torsion Bar Lift Procedure for 
Late Model Explorers
By:Andrew Brlic



Here is the procedure for giving your late model the inches you desire, while we wait for the aftermarket companies to design and market a true suspension lift.  It can be accomplished by anyone who is mildly mechanically inclined and only requires the following tools:

1 can Liquid Wrench (or any penetrating oil)
1 Jack and Jackstands
1 Socket Wrench
1 Measuring Tape

1. With the truck level, measure the distance from the center of the wheelwell lip to the top center of your wheel on each side.  Mark the distance for each side, it will be important for two reasons.  First you want to ensure that both sides are level when you're done, and second you want to limit the lift to no more than 2" from stock.  (Any higher will cause stress to your CV joints, resulting in accelerated wear and possibly failure) 




2. Now jack up the front end and secure on jackstands to take the pressure off the torsion bars.  Slide underneath and find the two adjuster bolts located near the back of both torsion bars (towards the rear of the truck) and spray liberally with some Liquid Wrench.  Let it soak in for 10 mins. to free up the bolts.  Using the socket wrench, tighten up the bolts until they are almost to the end of their travel.  This will torque up the torsion bars, causing them to lift the front end higher.  Now lower the front end and take the same measurements as you did before you began, to determine the lift gained.  Repeat the tightening/loosening of the bolts until both sides are level and lift gained is no more than 2". 




3. Take the truck out for a 10 minute drive.  This will cause the torsion bars to "settle" and will most likely give you 1.5-1.75" of final lift, which is ideally where you want to be.  The rear can be lifted using either extended shackles (limited lift) or by adding an add-a-leaf (full length recommended).  After the rear is lifted and you're content with the new height, be sure to take your vehicle to get an alignment, as you may have altered it after the torsion bar lift.  The combination of torsion bar lift and add-a-leaf does firm up the ride, but in my opinion improves it and in no way degrades it.  The Explorer is already a soft riding suspension, and after the lift body roll and nose dive is almost entirely eliminated.  So much so that I will be removing the rear swaybar in order to improve articulation (wheel travel).

It’s readily accepted that the late model Explorers will fit 31x10.5/15 tires at stock height, as my ’96 did.  I only experienced slight rubbing in the rear, and only during full compression while off-roading.  After the 2” lift front and 2.5” lift in the rear I have yet to experience any rubbing at all, even when putting the suspension to it’s limits.  I’m confidant that 32s could be easily fit after the lift, but I’m looking at a set of 33x10.5/15 tires to replace my 31s, once they are worn down, which will give me the height I desire, without the worry of rubbing from having too wide a tire.

Good luck.
Andrew Brlic



EXPLORER HOME | MORE EXPLORERS